The first thing that you should know when building circuits for electrical devices are the theories in basic electronics. Get to know the various components used in them and how to properly connect them to each other. And study how to make and read schematic diagrams that represents graphically the electrical circuit using images and symbols.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
A circuit is closed when electric current is being allowed passage through a path to ground from power source which indicates a functioning device normally. While the open one has broken the path and prevents movement when a machine is turned off. This is done using a switch so you can alternate between them rather than removing its source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Capacitors are components that stores electricity then discharges them when it drops and is measured in Farads with common ones being microfarad, nanofarad and picofarad. The commonly used types of capacitors are ceramic disc and electrolytic. The former being non polarized and the latter polarized requiring one of its leg to be properly connected with the power or ground.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
A circuit is closed when electric current is being allowed passage through a path to ground from power source which indicates a functioning device normally. While the open one has broken the path and prevents movement when a machine is turned off. This is done using a switch so you can alternate between them rather than removing its source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Capacitors are components that stores electricity then discharges them when it drops and is measured in Farads with common ones being microfarad, nanofarad and picofarad. The commonly used types of capacitors are ceramic disc and electrolytic. The former being non polarized and the latter polarized requiring one of its leg to be properly connected with the power or ground.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment